GSK 218MC/GSK218MC-H/GSK218MC-V Alarm

GSK 218MC/GSK218MC-H/GSK218MC-V Alarm List

Table4 The definition of the PLC extermal alarm
PMC alarm No.	A add.	Alarm Content
1200	A000.0	Air pressure detection abnormality
1201	A000.1	Lubrication detection abnormality
1202	A000.2	Lubricating motor detection abnormality
1203	A000.3	Cooling motor overload
1204	A000.4	Chip-removal motor detection abnormality
1205	A000.5	Pressure grease pump motor detection abnormality
1207	A000.7	Machine llumination lamp detection abnormality
1208	A0010	Machine controllable cabinet temperature detection abnormality
1209	A001.1	Machine body temperature detection abnormality
1210	A001,2	Machine vibration frequency detection abnormality
1211	A001.3	Pressure grease temperature detection abnomality
1212	A0014	Excessive low of the pressure grease
1213	A0015	Fail to ready the machine
1214	A0016	Fail to rotate the spindle because its shift is abnormal
1215	A001.7	Firstly perform the T code and then execute the M06 code
1216	A002.0	Fail to rotate the spindle in the tool releasing state
1217	A002.1	Spindle rotation tool can not be released
1218	A002.2	Tool magazine abnormal stop, confirm the tool number again
1219	A002.3	Fail to rotate the spindle because the manipulator is out of the origin
1220	A002.4	Spindle tool clamping detection abnormality
1221	A002.5	Spindle tool releasing detection abnormality
1222	A002.6	Spindle unit temperature detection abnormality
1223	A002.7	Spindle velocity detection abnormality
1224	A003.0	Spindle motor enabling detection abnormality
1225	A003.1	Spindle orientation in-position detection abnormality
1226	A003.2	Spindie shift abnormality
1227	A003.3	Failure to cycle start because the manipulator is out of the origin position
1228	A003.4	Failure to cycle start because the tool case is in the vertical position.
1229	A003.5	Firstly perform the mechanical zero return when executing the M06 code
1230	A003.6	Fail to perfom the tol-change when the spindle tool is in the releasing state
1231	A003.7	Fail to perfom the tool-change when the tool case is not in the horizontal position
1232	A004.0	Tool magazine rotation in-position detection abnormality
1233	A004.1	Tool magazine rotation motor overload

PMC A add. Alarm Content alarm No.
1234	A004.2	Manipulator motor overload
1235	A004.3	Tool magazine motion in-position detection abnormality
1236	A004.4	Tool magazine zero turn detection abnormality
1237	A004.5	Tool magazine origin position lost, return to the zero again
1238	A004.6	Tool case horizontal/vertical detection abnormality
1239	A004.7	Fail to rotate the spindle because the tool case is out of the horizontal position
1240	A005.0	Tool magazine abnormality, return to the zero again
1241	A005.1	Tool case vertical direction detection abnormality
1242	A005.2	Tool case horizontal direction detection abnormality
1243	A005.3	Tool magazine zero position setting enabled
1244	A005.4	Tool-change abnormal stop to sure the normal tool magazine
1245	A005.5	There is no code tool number in the table or code tool number is repeated
1246	A005.6	Spindle releasing/clamping detection abnormality
1247	A005.7	Spindle orientation time-sequence detection abnormality
1248	A006.0	Adequate condition for T code tool number
1249	A006.1	Fail to infeed but the spindle is with tool
1250	A006.2	Fail to infeed because the current tool number is different between the spindle and tool magazine
1251	A006.3	Turn off the power
1252	A006.4	Do not move the Z axis when tool clamping
1253	A006.5	Carefully operate the tool magazine debugging mode
1254	A006.6	Do not cycle start in the tool magazine debugging mode
1255	A006.7	Fail to return to the origin when tool clamping
1256	A007.0	Fail to the tool-change position when tool clamping
1257	A007.1	Fail to return to the tool-change position because the spindle under positioning
1258	A007.2	Fail to return to the tool-change position because the tool abnormality
1260	A007.4	Do not cycle start in the manual tool-change position return
1261	A007.5	Fail to retract due to out of the origin
1262	A007.6	Exceed the safety position
1263	A007.7	Carefully operate the manipulator debugging mode
1264	A008.0	Spindle velocity position mode conversion abnormality
1265	A008.1	Spindle position velocity mode conversion abnormality
1267	A008.3	Fail to operated because the tool case does not vertical to the manipulator
1268	A008.4	Fail to operate because the manipulator does not at the origin
1269	A008.5	Manipulator operation abnormality interruption
1270	A008.6	Manipulator tool inspection abnormality
1271	A008.7	Fail to operate the manipulator because the spindle does not orientate
1272	A009.0	Fail to operate the manipulator because the spindle tool does not

PMC alarm No.	A add.	Alarm Content
		release
1273	A009.1	Fail to operate the manipulator because the spindle tool does not clamp
1274	A009.2	Do not perform the tool-pivoting because the manipulator does not at the origin
1275	A009.3	Do not perform the tool-retraction because the manipulator does notat the origin
1276	A009.4	Do not rotate the cutter-head because the manipulator does not at the origin
1277	A009.5	Do not rotate the cutter-head because the tool case does not put on the horizontal place
1278	A009.6	The manipulator can not be operated because the Z axis does not return to the 2nd reference position.
1279	A009.7	Manipulator origin detection abnormality
1280	A010.0	Enforce to stop the rotation because the tool magazine rotation abnormality
1288	A011.0	Index worktable releasing/clamping detection overtime
1289	A011.1	Index worktable clamping/releasing detection abnormality
1290	A011.2	Fail to use the index worktable clamping equipment
1291	A011.3	Fail to rotate because the index worktable does not release
1292	A011.4	Fail to move because the index worktable does not clamp
1293	A011.5	Do not cycle start because the safety door opens
1294	A011.6	Do not shift in the rigid tapping, it is necessary to cancel the rigid tapping and then shift.
1 360	A020.0	Low lubrication pressure grease level