(Tool compensation)

 

Part 1: Familiar with the operation of the machine tool panel (one to eight, three or four of which are read by yourself, practice by yourself, or not) Part 2: Practice tool setting and check that the force is correct (Ninety-two) Part 3: Machining Parts (thirteen nineteen)

 

, Write a new program: (Example: Write program 01) Edit every 사 0고back (cannot be renamed with an existing program) Open a program: (Example: Open program 01) 시0고Back

 

Copy the current program to the newly created program

 

Example: Copy program %01 to the newly created program %08 program

 

First open the %01 program, search for 시08-시, copy is complete

 

Fourth, rename the current program

 

Example: Change program name %01 to program name %08

 

First open the %01 program 시-08 to rewrite, the name change is completed

 

, Delete a program: (example: except program 01) edit 시고 delete back

 

6. All programs are just removed at once: {Edit every 시-remove back

 

7. Rotate the tool post: (Example: Turn the tool post to No. 1 tool position)

 

Method: Manual-T10 or T11-Enter

 

Method 2: Manual-(tool change)

 

 

 

8. Clear tool compensation value: compensation (move the cursor to the required tool number) and return to the year

 

Nine. Align the No. 1 cylindrical knife (turn the tool holder to T10)

 

Z direction: Manually turn the annual knife forward in the x-axis direction and the annual knife end is about 05m), then retract the tool in the axis direction, and press the zone to return (the input data will disappear automatically at this time)

 

X direction: "Turn the hand forward to move the year of the year to the outer circle of the axis of the year, and then move it back in the direction of the axis to measure the outer diameter, and press

 

2532 (if the outer circle measurement value is 925.32) return (the data entered at this time automatically disappear)

 

, Turn the tool holder to T20 for the No. 2 cutting knife)

 

The method is the same as for the No. 1 external circular knife. (Note: When facing the Z direction, since the end face of the No. 1 tool has been turned, the No. 2 tool cannot be turned again

 

The end face can only be touched lightly. )

 

 

 

 

 

11. For No. 3 thread cutter (turn the tool holder to T30):

 

The method is the same as for No. 1 and No. 2 knife. Note that when facing the Z direction, since the annual tool tip is 60 degrees, the tool tip cannot touch the end face lightly.

 

The tip of the tool can only be substantially aligned with the end face.

 

12.Check whether the tool setting is correct: (remember to bring tool compensation when checking)

 

When inspecting the Z direction, the turning tool should be outside the diameter of the blank;

 

When checking the direction, the annual tool should be outside the end face of the blank to prevent the turning tool from directly colliding with the blank

 

Method one starts with bad operation (Note: When the cycle starts, you should put your hand next to the emergency stop button to observe whether the knife is positioned correctly)

 

No. 1 cylindrical knife (turn the tool holder to T11):

 

Direction: Press back to the military ring to start (check whether the tip of the knife is facing the end

 

X direction: Press 25.32 (if the measured value of the outer circle is 2532) to return to the annual ring start to check whether the tip of the annual knife is in

 

Above the outer circle of 925.32.

 

Cut off No. 2 (turn the tool holder to T22): The inspection method is the same as that of the No. 1 tool

 

No. 3 thread cutter (turn the tool holder to T33): The inspection method is the same as that of No. 1.

 

Method 2: Shake with handwheel

 

No. 1 outer circle (turn the tool post to T11): Turn the year to Z0 with the handwheel, and check whether the tip of the turning tool is aligned with the end face;

 

Shake the annual knife to X25.32 with the handwheel (if the measured value of the outer circle is 25.32), check whether the turning tool tip is

 

No on the 25.32 outer circle.

 

Cutting force No. 2 (turn the tool post to T22): The inspection method is the same as that of the No. 1 tool.

 

No. 3 thread cutter (turn the tool holder to T33); the inspection method is the same as that of No. 1.

 

13. Tool setting of workpieces of different lengths

 

Example: Originally the workpiece clamp length was 80mm or any length during tool setting. Now the workpiece clamp length is 40m. The tool should be re-calibrated during processing.

 

 

 

 

14. Modify knife compensation:

 

1. In order to prevent the outer circle car from being small, the diameter size of the drawing should be pre-0.3, the modification method is: cutter compensation one cursor moves to the required number input -.3 rewrite

 

2. If the outer circle is still larger than 0.32, the modification method is:

 

Move the cursor to the tool number for tool compensation 1.

 

Five, program tool graphics dry run: automatic dry run Guoshu ring start (press T twice to switch graphics and trajectory graphs)

 

16. Program tool tip trajectory dry run: automatic ten dry run and ten standby ring starting countries (press T twice to switch between graphics and trajectory diagrams)

 

Seven, automatic processing of parts: first move the year to a safe position where the rotating tool post does not touch the workpiece.

 

When you open the program and start the first part in a cycle, you should adjust the multiplier to 25% next to the left-hand emergency button. If there is an emergency or you find that the line of the knife is not the programmed line you expected, you should immediately be anxious and repeat the process.

 

Do not use more than one part).

 

Note: In batch processing, the length of the workpiece from the jaws should be compared with the length of .5m, leaving the end face. The length of each clamp is the same as possible. Run directly

 

18. Program suspension:

 

) During the automatic processing operation program, if you want to stop halfway to check the size of the part, the operation method is "Pause

 

(2) After pausing, if you want to continue processing, the operation method is: the difference between reset and pause when Zhengte Tenhuan starts the running program:

 

When the program is running, if you want to stop in the middle, if you press the reset button and want to continue adding, it will run down from the first line of the program; if you press the pause button and you want to continue processing, you will start from the line where the program was paused. run

 

Nine, select a segment to run in the program:

 

When selecting a segment, the row with the knife number should be selected. (Remember to move the knife to a safe position where the rotating tool post does not touch the workpiece)

 

Example: If the diameter of the groove is still large, you should modify the tool offset first, and then press the automatic input (the cursor moves 22M03S1)

 

This line, return to Junqi (when looking for a bad view, you should put your hand next to the emergency stop button and observe whether the positioning of the turning tool is correct)

 

Note: It is not possible to ask for selected passages in the follow-up procedure.